1.2343(H11/X38CrMoV5/Z38CDV5) ESR HOT-WORK STEEL
产品参数
- 冶炼方式: EAF+LF+VD
- 执行标准: ASTM 、DIN 、EN 、
- 产品尺寸: 350mm x 510mm x L
- 交货状态: 锻造 、
- 表面状态: 车光 、
- 库存状态: 查看库存
库存表
| 钢号 | 规格 mm | 重量 kg |
|---|---|---|
| 1.2343ESR | Dia 152mm Length: 2690mm | 1210 |
| 1.2343ESR | Dia 152mm Length: 3505mm | 2967 |
| 1.2343ESR | Dia 162mm Length: 2835mm | 4312 |
| 1.2343ESR | Dia 172mm Length: 3780mm | 3546 |
| 1.2343ESR | Dia 182mm Length: 3385mm | 3321 |
| 1.2343ESR | Dia 202mm Length: 4865mm | 4321 |
| 1.2343ESR | Dia 212mm Length: 4245mm | 1345 |
| 1.2343ESR | Dia 353mm Length: 3925mm | 3235 |
| 1.2343ESR | Dia 403mm Length: 2875mm | 3389 |
| 1.2343ESR | Dia 453mm Length: 3200mm | 2121 |
| 1.2343ESR | Dia 533mm Length: 3550mm | 3077 |
| 1.2343ESR | Dia 653mm Length: 3400mm | 8799 |
| 1.2343ESR | Dia 753mm Length: 2705mm | 9033 |
| 1.2343ESR | Dia 853mm Length: 1720mm | 7666 |
| 13Cr11Ni2W2MoV, 1Cr11Ni2W2MoV, 961 | All | 1118 |
| 13Cr11Ni2W2MoV, 1Cr11Ni2W2MoV, 961 | All | 1125 |
| 13Cr11Ni2W2MoV, 1Cr11Ni2W2MoV, 961 | All | 2111 |
| 13Cr11Ni2W2MoV, 1Cr11Ni2W2MoV, 961 | All | 1199 |
| 13Cr11Ni2W2MoV, 1Cr11Ni2W2MoV, 961 | All | 1189 |
产品详情
GH1131 : GB/T 14992 (2005) 化学成分
| C | Cr | Mo | Ni | W | Nb | Si | Mn | P | S | B | N |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ≤ 0.10 | 19.0 - 22.0 | 2.80 - 3.50 | 25.0 - 30.0 | 4.80 - 6.00 | 0.70 - 1.30 | ≤ 0.80 | ≤ 1.20 | ≤ 0.020 | ≤ 0.020 | ≤ 0.005 | 0.15 - 0.30 |
GH1131 : GB/T 14992 (2005) 力学性能
| 热处理 | 最小值 | 最大值 | 近似值 | 备注 |
|---|
| 热处理 | 最小值 | 最大值 | 近似值 | 备注 |
|---|
| 热处理 | 最小值 | 最大值 | 近似值 | 备注 |
|---|
| 热处理 | 最小值 | 最大值 | 近似值 | 备注 |
|---|
| 热处理 | 最小值 | 最大值 | 近似值 | 备注 |
|---|
| 热处理 | 类型 | 最小值 | 最大值 | 近似值 | 备注 |
|---|
DESIGNATION
| GB | DIN | AFNOR | UNI | AISI | Japan |
|---|---|---|---|---|---|
| 4Cr5MoSiV1 | X38CrMoV5-1 | Z38CDV5 | X37CrMoV5-1 KU | H11 | SKD6 |
STRENGTH:
≈ 780 N/mm²
THERMAL CONDUCTIVITY AT 200 °C:
27 W/m K
CHARACTER:
high-alloy hot-work steel with high toughness and heat resistance, hot cracks resistance and good thermal conductivity; for very high requirements available in grade *ESR (Electro-Slag Remelted)
APPLICATION:
molding plates and inserts for plastic injection mold tools; *ESR for applications for die casting (Al, Mg, Zn)
TREATMENT BY
highly suitable:
Polishing
very easily feasible (graining):
Etching
EDM:
in the hardened and tempered condition, treat again for stress relief about 20 °C below the last tempering temperature
Nitriding:
increases the wear resistance and prevents the bonding of casting material
Hard chroming:
in special cases
HEAT TREATMENT:
Annealing:
750 to 800 °C, about 4 to 5 hours slow controlled cooling of 10 to 20 °C per hour to about 600 °C; further cooling in air, max. 205 HB
Hardening:
1000 to 1040 °C
15 to 30 minutes keeping curing temperature
quenching in water/oil/air
obtainable hardness: 50−56 HRC
Nitriding:
Before nitriding stress-relief annealing is recommended at 550 °C. (Meusburger standard)
A treatment at 525 °C in ammonia gas results in a surface hardness of approx. 55 HRC
Tempering:
slow heating to tempering temperature immediately after hardening; minimum time in furnace: 1 hour per 20 mm part thickness; repeated tempering is recommended